Looking at the development of the large-screen
display industry in recent years, it is not difficult to see that seamless and high image quality are the ultimate pursuit of large-screen displays. In the current mainstream display technology, LCD splicing has more obvious seams, so it is more difficult to impact on areas with higher picture integrity, such as the broadcast room and the Meteorological Bureau. This field is also the core battlefield where small-pitch LEDs attack DLP. Although the technology is very mature, but in the process of using it will always encounter this and that kind of problems, the following will mainly introduce the common faults and solutions of the . 1. What is the reason why the LED screen appears completely black? In the process of using the control system, we occasionally encounter the phenomenon that the LED screen appears completely black. The same phenomenon may be caused by a variety of different reasons, even the process of turning the screen black will vary with different operations or different environments. For example, it may be black as soon as it is powered on, or it may become black during the loading process, or it may become black after sending, etc.: 1, please make sure that all hardware including the control system is complete Power on correctly. (+5V, do not connect reversely or wrongly) 2, check and double-check whether the serial port cable used to connect to the controller is loose or disconnected. (If it turns black during the loading process, it is probably caused by this reason, that is, the communication line is interrupted due to the loosening of the communication line during the communication process, so the screen turns black. Do not think that the screen body is not moving, and the line cannot be loosened. Please check it by hand, it is very important to solve the problem quickly.) 3. Check and confirm whether the LED screen and the HUB distribution board connected to the main control card are tightly connected and whether they are plugged in reverse. 2. Why the bright lines appear for a few seconds or the screen becomes blurred when the is first powered on? After the screen controller is properly connected to the computer and the HUB distribution board and the screen, you need to provide +5V power to the controller to make it work normally (at this time, do not directly connect to 220V voltage). At the moment of power-on, a bright line or screen will appear on the screen for a few seconds. This bright line or screen is a normal test phenomenon and reminds the user that the screen is about to start working normally. Within 2 seconds, the phenomenon will be automatically eliminated, and the screen will enter the normal working state. 3. The reason why the whole screen is not bright or dim on the unit board is 1. Visually check whether the power connection line, the 26P cable between the unit boards and the power module indicator are normal. 2. Use a multimeter to measure whether the unit board has normal voltage, and then measure whether the voltage output of the power module is normal. If not, it is judged that the power module is broken. 3. Measure the low voltage of the power module, and adjust the fine adjustment (the fine adjustment of the power module near the indicator light) to make the voltage reach the standard. 4. What is the reason why it cannot be loaded or communicated? The reasons for communication failure and loading failure are roughly the same, which may be caused by the following reasons. Please check with the operation according to the listed items: 1. Make sure that the control system hardware is correctly powered on. 2. Check and confirm that the serial cable used to connect to the controller is a straight-through cable, not a crossover cable. 3. Check and confirm that the serial port cable is intact and there is no looseness or fall off at both ends. 4. Select the correct product model, correct transmission method, correct serial port number, correct serial transmission rate according to the touch display control software and the control card you choose, and set it correctly according to the dial switch diagram provided in the software Control the address bits and serial transmission rate on the system hardware. 5. Check whether the jumper cap is loose or falling off; if the jumper cap is not loose, please make sure that the direction of the jumper cap is correct. 6. If it still fails to load after the above inspection and calibration, please use a multimeter to measure whether the serial port of the connected computer or control system hardware is damaged to confirm whether it should be returned to the computer manufacturer or the control system hardware The body is returned for testing. manufacturer LED full color display electronic display
Top One Tech Ltd. is fully committed to supplying high quality products and services.
Top One Tech Ltd. ’s mission is to be the leading global innovator, developer and provider of About Us lcd monitor supplier products, systems, and services.
Consumers like these are interested not just in About Us they will spend their money on, but also in the human and environmental impact of the supply chain that produces those goods.
