Eight points determine the quality of the LED full-color display!

Abstract: 1. Anti-static 　　 display assembly factory should have good anti-static measures. Dedicated anti-static ground, anti-static floor, anti-static soldering iron, anti-static table mat, anti-static ring, anti-static clothing, humidity control, equipment grounding (especially the foot cutter), etc. are all basic requirements, and should be checked regularly with a static meter . 2. Drive circuit design 　　 display screen 1. Anti-static 　　 display assembly factory should have good anti-static measures. Dedicated anti-static ground, anti-static floor, anti-static soldering iron, anti-static table mat, anti-static ring, anti-static clothing, humidity control, equipment grounding (especially cutting machine), etc. are all basic requirements, and should be checked regularly with a static meter . 2. Drive circuit design The arrangement of the drive IC on the drive circuit board on the display module will also affect the brightness of the LED. Since the output current of the driver IC is transmitted over a long distance on the PCB board, the voltage drop of the transmission path will be too large, affecting the normal operating voltage of the LED and causing its brightness to decrease. We often find that the brightness of the LEDs around the display module is lower than in the middle, which is why. Therefore, to ensure the consistency of the display screen brightness, it is necessary to design a good drive circuit distribution diagram. 3. Design current value The nominal current of the LED is 20mA. Generally, it is recommended that its maximum use current be no more than 80% of the nominal value, especially for displays with small dot pitch, due to poor heat dissipation conditions, the current value should be lowered. . According to experience, due to the inconsistency of the attenuation speed of the red, green, and blue LEDs, the current value of the blue and green LEDs should be reduced in a targeted manner to maintain the consistency of the white balance after the display screen is used for a long time. 4. Mixed lights 　　 LEDs of the same color and different brightness levels need to be mixed, or inserted according to the light insertion diagram designed according to the discrete law to ensure the consistency of the brightness of each color on the whole screen. If there is a problem in this process, the local brightness of the display screen will be inconsistent, which will directly affect the display effect of the LED display screen. 5. Control the verticality of the lamp. For in-line LEDs, there must be sufficient process technology to ensure that the LEDs are perpendicular to the PCB board when passing the furnace. Any deviation will affect the brightness consistency of the LED that has been set, and color blocks with inconsistent brightness will appear. 6. The temperature and time of wave soldering must be strictly controlled. The temperature and time of wave soldering must be strictly controlled. It is recommended that the preheating temperature is 100℃±5℃, and the highest temperature should not exceed 120℃. The preheating temperature must rise smoothly, and the soldering temperature It is 245°C±5°C, and the welding time is recommended to be no more than 3 seconds. Don't vibrate or shock the LED after the furnace, until the normal temperature is restored. The temperature parameters of the wave soldering machine should be checked regularly. This is determined by the characteristics of the LED. Overheating or fluctuating temperature will directly damage the LED or cause hidden quality problems, especially for small-sized round and oval LEDs such as 3mm. 7. Welding control When the touch display does not light up, there is often more than 50% probability that it is caused by various types of virtual welding, such as LED pin welding, IC pin welding, header pin header welding, etc. Wait. The improvement of these problems requires strict improvement of the process and strengthened quality inspection to solve. The vibration test before leaving the factory is also a good inspection method. 8. Heat dissipation design 　　 LED will generate heat when working, too high temperature will affect the attenuation speed and stability of the LED, so the heat dissipation design of the PCB board and the ventilation and heat dissipation design of the cabinet will affect the performance of the LED. LED unit board LED full color display LED module wholesale
Technology is a foundational component of today's fast-paced business environment. Top One Tech Ltd. who are digital natives are especially equipped to harness technology's power to establish, promote and grow our businesses.
The guiding vision of Top One Tech Ltd. is 'Bringing the best to everyone we touch'. By 'The best', we mean the best products, the best people and the best ideas.
It's the consistent experience that builds trust and loyalty. Creating a personality and platform that is scalable will allow you to evolve About Us with your consumers.
Loyalty programs provide an opportunity to learn the preferences of customers and design communication strategies that will resonate with About Us.
Top One Tech Ltd. provides professional , technology and human expertise clients need to find trusted answers. Go to Toponetech touch display for answers.